Aero­dynamics: Scoring decimal points

“We shouldn’t forget, however, that when it comes to designing efficient aerodynamics, electric vehicles offer distinct advantages. For instance, it’s only thanks to the battery and dispensing with an exhaust system that we were able to create an enclosed and very smooth underfloor from nose to tail. There was a lot of back and forth with our colleagues in chassis development to make sure all the main axle components remain concealed beneath underfloor panels. Everything—including tunnel, fuel tank and exhaust system—that’s responsible for air turbulence around cars with internal combustion engines no longer exists in the same form on electric vehicles. For aerodynamics, this is a tremendous plus. What’s more, an electric motor is much more efficient than a combustion engine. It not only releases less heat into the environment but does not require as much cooling nearly as often. Consequently, we are able to develop thermal management concepts that are beneficial to aerodynamics. The active inlet louvers on our Audi e-tron models’ Singleframe grilles are a case in point—and a pivotal aerodynamic measure at the front end. An electronically operated louver system on each of the two air inlets can be automatically opened or closed, depending on the degree of cooling the vehicle requires. We aerodynamicists like to say that the louvers should always remain closed so that no air flows through the car and causes losses. Instead, the air should flow over and under the vehicle. But the control system also has to respond to other needs, such as when occupants want to climatize the interior. That’s when the louvers open. Despite that, our highly intelligent thermal management ensures that the louvers remain shut for most of the driving cycle, thus lowering the cd value.”

“One of our goals as aerodynamicists is to come up with innovative technical details that give the designers greater scope for creativity. This is done best when we collaborate in solving specific issues. When developing a vehicle’s aerodynamic details, we work from front to rear. After all, if we make a mistake with the airflow at the front, we usually can’t correct it again at the rear.”

“Air arrives at the front nose of the vehicle thereafter passing above, below and along its sides. Ensuring it flows as smoothly as possible along the sides is an art unto itself. The short overhangs that our designers use to make electric vehicles so attractive pose a really big challenge to us aerodynamicists. They leave us with very little space to deflect the air along the sides after it hits the front at high speed. That’s why we work with air curtains at the side of the car’s nose. These air inlets are like vanes that basically catch the air at the front, quickly guiding it inward and keeping it close to the vehicle body, before channeling it into the wheel arch. If we didn’t have these air curtains, the vehicle would offer a wider surface for the air, which would increase the drag coefficient.”

“It might sound trivial but we can use the water management finisher on the A-pillar to smoothly form the surface and greatly optimize the flow from the front along the arc of the A-pillar. If we didn’t do this, it would result in substantial aerodynamic losses. When the airflow then interacts with the exterior mirror. This is a true challenge in aerodynamic terms. A conventional exterior mirror greatly displaces the oncoming flow and influences the airflow until far behind the vehicle. That’s why I’m incredibly pleased that we offer virtual exterior mirrors as an option on our Audi e-tron models. The WLTP cycle shows that their influence on the drag coefficient improves the range by the equivalent of around 2.5 kilometers compared with conventional exterior mirrors. This improvement is even more pronounced on country roads and highways.

“Our Audi designers love making a nice curved transition from the side to the rear of the vehicle. However, that’s a real challenge in aerodynamic terms because the air current doesn’t really know where it should separate. “Curved” always results in greater instability. Sometimes the airflow separates in one place, sometimes in another, which results in poor aerodynamics. But, of course, we can’t design an Audi with sharp-edged tail. Instead, we integrate the edges needed to ensure a clean break in the air flow into the rear lights—they follow the same contours as the interior graphics of the lights. This maintains the harmonious appearance of the outer skin and avoids unpleasant refraction of the light. These separation edges on the rear lights are a perfect example of how we work with the designers to optimize innovations on a model in the wind tunnel.”

“One example: In a new Audi e-tron model being launched in 2021, there’s a seal in the joint between the side panel frame and the tailgate. Just this seal produces an improvement of five thousandths in the drag coefficient. You might think that it’s just a small gap without this seal. But the pressure ratios between the side and the rear of the car are so extreme that air is sucked into the joint and instantly results in losses. By contrast, using this seal improves the drag coefficient by five thousandths. In the WLTP cycle, this adds around three kilometers to the range. So you see, even the tiniest details will make all the difference going forward.”